Linux+ XK0-005 Exam Dumps

The cause of the issue is that the CIDR value /33 is invalid for an IPv4 address. The CIDR value represents the number of bits in the network prefix of an IP address, and it can range from 0 to 32 for IPv4 addresses. A CIDR value of /33 would imply a network prefix of more than 32 bits, which is impossible for an IPv4 address. To assign a temporary IP address/netmask of 192.168.168.1/255.255.255.255 to eth0, the CIDR value should be /32 instead, which means a network prefix of 32 bits and a host prefix of 0 bits. There is no route to 192.168.168.1/33 is not the cause of the issue, as the ip address add command does not check the routing table. The interface eth0 does not exist is not the cause of the issue, as the ip address add command would display a different error message if the interface does not exist. The IP address 192.168.168.1 is already in use is not the cause of the issue, as the ip address add command would display a different error message if the IP address is already in use. References: [CompTIA Linux+ (XK0-005) Certification Study Guide], Chapter 13: Networking Fundamentals, page 435.

The systemct1 reboot command will restore the server to its usual target by rebooting it. This will cause the server to load the default target specified in /etc/systemd/system.conf or /etc/systemd/system/default.target files. The telinit 0 command would shut down the server, not restore it to its usual target. The systemct1 get-default command would display the default target, not change it. The systemct1 emergency command would switch the server to emergency.target mode, which is even more restrictive than rescue.target mode. References: [CompTIA Linux+ (XK0-005) Certification Study Guide], Chapter 17: System Maintenance and Operation, page 516.

The administrator can use the following two options to boot the system into the single user mode:

Interrupt the boot process in the GRUB menu and add systemd.unit=rescue.target in the kernel line. This option will boot the system into the rescue mode, which is a minimal environment that allows the administrator to perform basic tasks such as repairing the system. The GRUB menu is a screen that appears when the system is powered on and allows the administrator to choose which kernel or operating system to boot. The kernel line is a line that specifies the parameters for the kernel, such as the root device, the init system, and the boot options. The administrator can interrupt the boot process by pressing the e key in the GRUB menu and edit the kernel line by adding systemd.unit=rescue.target at the end. This option will tell the system to use the rescue target, which is a unit that defines the state of the system in the rescue mode. The administrator can then press Ctrl+X to boot the system with the modified kernel line. This option will boot the system into the single user mode and allow the administrator to troubleshoot the issues.

Interrupt the boot process in the GRUB menu and add systemd.unit=single.target in the kernel line. This option will boot the system into the single user mode, which is a mode that allows the administrator to log in as the root user and perform maintenance tasks. The GRUB menu and the kernel line are the same as the previous option. The administrator can interrupt the boot process by pressing the e key in the GRUB menu and edit the kernel line by adding systemd.unit=single.target at the end. This option will tell the system to use the single target, which is a unit that defines the state of the system in the single user mode. The administrator can then press Ctrl+X to boot the system with the modified kernel line. This option will boot the system into the single user mode and allow the administrator to troubleshoot the issues.

The other options are incorrect because they either do not boot the system into the single user mode (execute the following command from the GRUB rescue shell: mount -o remount, ro/sysroot or interrupt the boot process in the GRUB menu and add systemd.unit=single in the kernel line) or do not use the correct syntax (interrupt the boot process in the GRUB menu and add single=user in the kernel line or interrupt the boot process in the GRUB menu and add init=/bin/bash in the kernel line). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 8: Managing the Linux Boot Process, pages 267-268.

 The command docker images prune -a will help to remove all dangling images and delete all the images that do not have an associated container. The docker command is a tool for managing Docker containers and images. The images subcommand operates on images. The prune option removes unused images. The -a option removes all images, not just dangling ones. A dangling image is an image that is not tagged and is not referenced by any container. This command will accomplish the task of cleaning up the unused images. The other options are incorrect because they either do not exist (docker push images -a or docker images rmi --all) or do not remove images (docker rmi -a images only removes images that match the name or ID of “images”). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 19: Managing Cloud and Virtualization Technologies, page 567.