220-1201 VCE Exam Download

PoE (Power over Ethernet) allows both data and electrical power to be delivered over the same Ethernet cable. A PoE injector adds power to Ethernet cables for devices that need it.

From CompTIA A+ 220-1101 Official Study Guide, Objective 2.2 – Networking hardware:

“Power over Ethernet (PoE) technology and PoE injectors enable both power and data transmission to compatible network devices like access points and IP cameras.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 2: Network Hardware

CompTIA Exam Objectives 220-1101, Domain 2.2

============

Comprehensive and Detailed Step-by-Step Explanation:

When delivering 10Gbps speeds over long distances, fiber optic cables are the best choice. Here’s the breakdown:

A. Multimode Fiber (Correct Answer):

Multimode fiber is designed for relatively short to medium distances (up to 1,312 feet or 400 meters) while supporting high-speed data transfer (10Gbps and above).

It uses LED light sources and is cost-effective for environments like data centers or within buildings.

For the specified distance of over 328ft but under 1,312ft, multimode fiber is the most suitable option.

Incorrect Options:

B. Single-mode Fiber: While single-mode fiber supports much greater distances (up to several miles or kilometers) and higher speeds, it is more expensive and unnecessary for the specified range. Single-mode fiber is generally used for long-haul networking or telecommunications.

C. Cat 6a: Cat 6a is capable of 10Gbps speeds but only up to 328ft (100 meters). It cannot reliably handle the specified distance of over 328ft.

D. Cat 6: Cat 6 is also limited to 10Gbps speeds at distances up to 328ft (100 meters). Beyond this range, it is unsuitable.

Key Takeaway:

For delivering 10Gbps speeds over distances longer than 328ft (100m) but under 1,312ft (400m), Multimode Fiber is the best choice due to its ability to support high-speed data over medium distances at a reasonable cost.

Laptop display assemblies typically include not only the LCD panel but also the webcam, microphone, display cable, and critically, the Wi-Fi antennas. In most laptops, Wi-Fi antennas are built into the display bezel, because the elevated position allows for stronger wireless signal reception. When replacing the entire display assembly, the antennas must be carefully disconnected and reconnected during reinstallation.

CompTIA A+ emphasizes proper cable routing and antenna reattachment as essential steps in laptop hardware disassembly and reassembly. Failing to reconnect these antennas results in weak or nonfunctional wireless connectivity, even though the display replacement itself may be successful.

Heat sinks and CPU fans are located on the motherboard and are unrelated to display assembly replacement. Resetting BIOS settings is unnecessary unless troubleshooting firmware-related issues, not replacing hardware components like a display. Therefore, the only action that aligns with standard laptop design and CompTIA A+ procedures is ensuring that the wireless antennas are reconnected.

Thus, the correct answer is B.

A tablet’s display is made of two key parts that work together: the LCD (or OLED) that shows the image, and the digitizer that detects touch input. If the screen image looks normal but the device does not respond to taps, swipes, or gestures, the most likely failed component is the digitizer (or the digitizer layer/cable). The digitizer is a transparent sensor grid that converts touch into signals the system can interpret. When it fails, the tablet may still power on and show a clear picture, but touch will not register at all or will behave erratically.

Because the device shows no physical damage and a system reset does not fix the issue, this points away from a software glitch and toward a hardware input failure. Replacing the LCD screen is typically indicated when you see display problems such as no image, distorted colors, flickering, dead pixels, or backlight issues—not purely touch failure. A battery problem would affect power/charging, not touch responsiveness. A motherboard replacement is far more invasive and not the most likely first hardware fix for a touch-only failure. Therefore, the correct component to replace is the digitizer.