Pure Storage FlashArray-Implementation-Specialist Questions Answers

To verify the history and transmission status of Phonehome log bundles, the correct command is purearray phonehome --list .

Before starting a controller upgrade (NDU), it is mandatory to ensure that the array can successfully transmit diagnostic data to Pure Storage. This allows Support to review the "pre-flight" checks and ensures that if an issue occurs during the upgrade, logs will be available for triage.

Usage: Running purearray phonehome --list displays a table of recent log bundles generated by the system.

Verification: The Engineer must look at the Status column for the most recent entries. A status of "uploaded" confirms that the array has successfully connected to the Pure Storage cloud and transferred the data. If the status is "queued" or "failed," the upgrade should not proceed until network connectivity (firewall/proxy) is resolved. Options A and C are incorrect CLI syntax for this specific verification task.

The FlashArray//XL series has a specific, validated slot population rule for its PCIe cards to ensure optimal performance and thermal management. For a standard Fibre Channel (FC) configuration on a FlashArray//XLR5 , the factory default shipment includes a specific arrangement of host I/O cards and offload engines.

The correct default configuration is:

PCIe Slot 3: 4-Port 32Gb FC card.

PCIe Slot 5: 2-Port 32Gb FC card.

PCIe Slot 6: DirectCompress Accelerator (DCA).

This layout (Option B) adheres to the //XL's architecture where specific slots are prioritized for frontend host I/O (like slots 3 and 5) and others for offload functions or backend connectivity. Implementation Engineers must verify cards are in these exact slots during the visual inspection. If cards are moved to incorrect slots (like slot 1 or 4 for primary FC in this specific config), the array may not boot or may fail to initialize the FC services correctly due to BIOS enumeration orders.

=========

The FlashArray//X70 (R2/R3) and FlashArray//X90 (R2/R3) require 1600W Power Supply Units (PSUs) .

Pure Storage equips its FlashArray//X chassis with different power supply capacities based on the compute load of the installed controllers:

Performance Tier (X70/X90): These models utilize high-core-count Intel Xeon processors and support the maximum density of NVMe DirectFlash Modules. To support the peak power draw of these components while maintaining N+1 redundancy (where one PSU can support the entire load), the 1600W units are mandatory.

Entry/Mid Tier (X10/X20/X50): Lower-end models often ship with 1000W or 1200W PSUs (though X50 often uses 1600W in later revisions or specific configs).

Identification: Implementation Engineers can identify these PSUs by the label on the rear handle (often color-coded or explicitly marked "1600W"). Installing an X90 controller into a chassis with older 1200W PSUs (e.g., during an improper upgrade attempt) would likely trigger a hardware alert or prevent the controllers from booting due to insufficient power budget.

Adding an external DirectFlash Shelf (DFS) or a legacy SAS Expansion Shelf to a Pure Storage FlashArray requires precise physical cabling to ensure backend high availability. Because the controllers utilize an active/active backend topology—where both controllers must maintain redundant loops to every single capacity shelf—a single misplaced cable can cause a severe hardware fault.

Once the physical installation is complete, the Implementation Engineer must definitively validate the topology before handing the array over to production. To do this, they log into the local KVM console or SSH session using the restricted puresetup account. From here, the official Pure Storage post-installation procedure dictates running two specific Python validation scripts: storage_view.py enclosures and storage_view.py config .

While both are used, storage_view.py config is the primary command utilized to map the specific SAS or NVMe-oF (RoCE) port bindings. The script actively polls the physical ports on the rear of the controllers and traces the loops down through the I/O Modules (IOMs) on the shelves. If the cabling is flawless, the CLI will explicitly return: "No errors detected." If a cable is crossed (e.g., Controller 0 plugged into IOM 1 instead of IOM 0), the script will instantly flag the topology mismatch, allowing the engineer to correct it on the spot.