CWNA CWNA-108 Dumps PDF

OFDM is a modulation method that divides the channel bandwidth into multiple subcarriers, each carrying a single data symbol. This allows for higher data rates and more robust transmissions in multipath environments. OFDM was first introduced in the 802.11a standard, which operates in the 5 GHz band and supports data rates up to 54 Mbps. Later, the 802.11g standard adopted OFDM for the 2.4 GHz band, and the 802.11n and 802.11ac standards enhanced OFDM with features such as MIMO (Multiple Input Multiple Output), channel bonding, and higher-order modulation schemes to achieve data rates up to 600 Mbps and 6.9 Gbps, respectively. These standards are collectively known as the ERP (Extended Rate PHY), HT (High Throughput), and VHT (Very High Throughput) PHYs . References: [CWNA-109 Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 163; [CWNA-108 Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 157.

FT (Fast Transition) is an IEEE 802.11 standard method for fast roaming. FT is defined in the IEEE 802.11r amendment and is also known as Fast BSS Transition (FBT) or Fast Secure Roaming. FT is a feature that allows a client station to quickly switch from one AP to another within the same ESS (Extended Service Set) without having to re-authenticate and re-associate with each AP. This reduces the latency and packet loss that may occur during roaming, thus improving the user experience and maintaining the security of the connection. FT works by using pre-authentication and key caching mechanisms that allow the client station and the APs to exchange security information before the actual roaming occurs. This way, when the client station decides to roam to a new AP, it can use a fast reassociation request and response that contain only a few fields, instead of a full authentication and association exchange that require more time and data. References: 1, Chapter 9, page 367; 2, Section 6.3

When performing a post-deployment validation survey for voice over Wi-Fi (VoWiFi), an action that must be performed is Application analysis with an active phone call on a VoWiFi handset. Application analysis is a method of testing the performance of a specific application over the WLAN by measuring parameters such as throughput, latency, jitter, packet loss, MOS score, and R-value. Application analysis with an active phone call on a VoWiFi handset can help to evaluate the quality of service (QoS) and user experience of VoWiFi calls over the WLAN. It can also help to identify any issues or bottlenecks that may affect VoWiFi calls such as interference, roaming delays, or insufficient coverage. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 549; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 519.

Return loss is a measure of how well the components of an RF system are matched in terms of their impedance. Impedance is the opposition to the flow of alternating current in a circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. When the impedance of the source, the transmission line, and the load are not equal, some of the power is reflected back to the source, causing a loss of forward power. This loss is expressed in decibels (dB) as return loss. The higher the return loss, the lower the reflection and the better the impedance matching. Conversely, the lower the return loss, the higher the reflection and the worse the impedance matching.

VSWR (Voltage Standing Wave Ratio) is another way of expressing the same concept. It is the ratio of the maximum voltage to the minimum voltage along a transmission line due to the interference of the incident and reflected waves. A VSWR of 1:1 means that there is no reflection and perfect impedance matching. A VSWR higher than 1:1 means that there is some reflection and impedance mismatch. The higher the VSWR, the higher the reflection and the lower the return loss.

Therefore, a significant impedance mismatch between components in an RF system will cause high reflection, high VSWR, and low return loss.