NSE7_FSN_AR-7.6 Exam Dumps : Fortinet NSE 7 - Secure Networking 7.6 Architect

Based on the Fortinet FCSS - Network Security 7.6 documents and the analysis of the VPN tunnel exhibit, here is the verified answer.

Questions no: 91

Verified Answer: A, C

Comprehensive and Detailed Explanation with all FCSS - Network Security 7.6 documents:

To determine the status of the VPN tunnel, we must examine the specific counters and fields in the diagnose vpn tunnel list output provided in the exhibit.

Analyze Phase 2 Status (Option A):

The output displays child_num=0.

In IKEv2 (and IKEv1 implementations in FortiOS), " Child SAs " refer to the Phase 2 (IPsec) Security Associations that carry the actual data traffic.

A value of 0 indicates that no Phase 2 tunnels are established. If Phase 2 were up, child_num would be at least 1.

Additionally, under the proxyid section, the field sa=0 confirms there is no active Security Association for that traffic selector.

Analyze Traffic Status (Option C):

The stat line shows: rxp=0 txp=0 rxb=0 txb=0.

rxp (Received Packets) and txp (Transmitted Packets) are both zero. This definitively confirms that no traffic is traversing the tunnel currently. This is expected since Phase 2 is down.

Analyze Phase 1 Status (Why B is incorrect):

The tunnel entry exists in the list with a valid tun_id, and NAT-Traversal is active (natt: mode=keepalive).

The presence of the tunnel in this command output, along with active Keepalive mechanisms, typically indicates that Phase 1 (IKE SA) is established and the peers are communicating on port 4500 (NAT-T), even though the data tunnels (Phase 2) failed to negotiate. If Phase 1 were down, the tunnel would often not appear in this " list " view or would show different status flags indicating a complete connection failure.

Conclusion: The exhibit shows a scenario where the Phase 1 control channel is likely up (evidenced by the entry existence and NATT keepalives), but the Phase 2 data channel is down (child_num=0), resulting in zero traffic flow (rxp=0/txp=0).

The correct answers are A and D .

The debug output shows:

Sent RADIUS req to server ' RadiusServer ' : IP=172.25.188.164 ... user= " student " using CHAP

Result for radius svr ' RadiusServer ' 172.25.188.164(0) is 0

Sending result 0 for req 2

The study guide explains that in RADIUS real-time debug, FortiGate shows the IP address of the RADIUS server it is querying. In the example, it says FortiGate “creates an access request to the RADIUS server at IP address 10.0.13.130” and shows the line Sent radius req to server ... IP=10.0.13.130

So in your exhibit, the queried server is clearly 172.25.188.164 , which makes A correct.

The study guide also states:

“The message fnbamd_comm_send_result-Sending result 0 indicates that the authentication was successful and that FortiGate received the Access-Accept message.”

Since your exhibit also ends with Sending result 0 , that makes D correct.

Why the other options are wrong:

B is wrong because result 0 means authentication successful , not failed

C is wrong because the debug explicitly shows using CHAP , and the study guide lists supported RADIUS schemes as CHAP, PAP, MS-CHAP, and MS-CHAPv2

E is wrong because the study guide says two-factor authentication would involve an Access-Challenge response: “If two-factor authentication is enabled on the server, the response is an Access-Challenge message” Your exhibit shows successful result 0 / Access-Accept , not a challenge.

So the verified answers are: A, D .

The correct answers are B and D .

The study guide explains that in the SP Login Dump section, FortiGate is acting as the service provider (SP) , and that you should read these fields:

“The IdP SSO URL, from the setting idp-single-sign-on-url in the FortiGate configuration”

“The SP SSO URL, from the setting single-sign-on-url in the FortiGate configuration”

“The IdP Entity ID, from the setting id-entity-id in the FortiGate configuration”

“The SP Entity ID, from the setting entity-id setting in the FortiGate configuration”

In the exhibit:

Destination= " " → this is the IdP SSO URL

< lasso:RemoteProviderID > < /lasso:RemoteProviderID > → this is the IdP Entity ID

AssertionConsumerServiceURL= " " → this is the SP SSO URL

< saml:Issuer > < /saml:Issuer > → this is the SP Entity ID

The same study-guide example shows this exact mapping pattern, where:

Destination points to the IdP

AssertionConsumerServiceURL and Issuer point to the SP

Therefore:

10.1.10.2 is the IdP → D

10.1.10.254 is the SP → B

So the verified answers are: B, D .