Sure Pass Exam JN0-351 PDF

A firewall filter is a configuration that defines the rules that determine whether to forward or discard packets at specific processing points in the packet flow. A firewall filter can also modify the attributes of the packets, such as priority, marking, or logging.  A firewall filter can be applied to various interfaces, protocols, or routing instances on a Juniper device 1 .

A firewall filter has a family attribute, which specifies the type of traffic that the filter can evaluate.  The family attribute can be one of the following: inet, inet6, mpls, vpls, iso, or ethernet-switching 2 . The family inet firewall filter is used to evaluate IPv4 traffic, which is the most common type of Layer 3 traffic on a network.

To create a family inet firewall filter, you need to specify the appropriate match criteria and actions for each term in the filter. The match criteria can include various fields in the IPv4 header, such as source address, destination address, protocol, port number, or DSCP value.  The actions can include accept, discard, reject, count, log, policer, or next term 3 .

To apply a firewall filter to Layer 3 traffic that is being sent between VLANs, you need to apply the filter to the appropriate IRB interface. An IRB interface is an integrated routing and bridging interface that provides Layer 3 functionality for a VLAN on a Juniper device. An IRB interface has an IP address that acts as the default gateway for the hosts in the VLAN.  An IRB interface can also participate in routing protocols and forward packets to other VLANs or networks 4 .

Therefore, option C is correct, because you should create a family inet firewall filter with the appropriate match criteria and actions. Option D is correct, because you should apply the firewall filter to the appropriate IRB interface.

Option A is incorrect, because you should not create a family ethernet-switching firewall filter with the appropriate match criteria and actions. A family ethernet-switching firewall filter is used to evaluate Layer 2 traffic on a Juniper device.  A family ethernet-switching firewall filter can only match on MAC addresses or VLAN IDs, not on IP addresses or protocols 5 .

Option B is incorrect, because you should not apply the firewall filter to the appropriate VLAN. A VLAN is a logical grouping of hosts that share the same broadcast domain on a Layer 2 network. A VLAN does not have an IP address or routing capability.  A firewall filter cannot be applied directly to a VLAN; it must be applied to an interface that belongs to or connects to the VLAN 6 .

A tunnel is a connection between two computer networks, in which data is sent from one network to another through an encrypted link. Tunnels are commonly used to secure data communications between two networks or to connect two networks that use different protocols.

Option B is correct, because tunnel endpoints must have a valid route to the remote tunnel endpoint. A tunnel endpoint is the device that initiates or terminates a tunnel connection. For a tunnel to be established, both endpoints must be able to reach each other over the underlying network.  This means that they must have a valid route to the IP address of the remote endpoint 1 .

Option D is correct, because tunnels add additional overhead to packet size. Tunnels work by encapsulating packets: wrapping packets inside of other packets. This means that the original packet becomes the payload of the surrounding packet, and the surrounding packet has its own header and trailer. The header and trailer of the surrounding packet add extra bytes to the packet size, which is called overhead.  Overhead can reduce the efficiency and performance of a network, as it consumes more bandwidth and processing power 2 .

Option A is incorrect, because BFD can be used to monitor tunnels. BFD is a protocol that can be used to quickly detect failures in the forwarding path between two adjacent routers or switches. BFD can be integrated with various routing protocols and link aggregation protocols to provide faster convergence and fault recovery. BFD can also be used to monitor the connectivity of tunnels, such as GRE, IPsec, or MPLS.

Option C is incorrect, because IP-IP tunnels are stateless. IP-IP tunnels are a type of tunnels that use IP as both the encapsulating and encapsulated protocol. IP-IP tunnels are simple and easy to configure, but they do not provide any security or authentication features. IP-IP tunnels are stateless, which means that they do not keep track of the state or status of the tunnel connection. Stateless tunnels do not require any signaling or negotiation between the endpoints, but they also do not provide any error detection or recovery mechanisms.

Default BGP keepalive timer in Junos is 30 seconds

The default keepalive time for BGP is 30 seconds, which means that BGP peers send keepalive messages to each other every 30 seconds to verify the liveness of the BGP session. If no keepalive message is received from a peer within the hold time, which is 90 seconds by default, the peer is considered to be unavailable and the BGP session is closed. The keepalive time and the hold time can be configured manually for each BGP peer or peer group, but they must match on both ends of the BGP session. The keepalive time should be one third of the hold time for optimal performance. Therefore, option C is correct and the other options are incorrect. References:  BGP keepalive messages and hold time - Juniper Networks