An aggregate has experienced a multiple disk failure due to a failing I/O module (IOM). The module has been replaced and the aggregate is still failed.
What step can be taken to recover the aggregate?
While setting up a replication between two clusters, an administrator receives the following error message:
Failed to create cluster peering with 'Error: RPC to peer address 192.168.31.10 failed'.
What is the cause of this issue?
Which two statements regarding drive 1.2.3.L1 are true? (Choose two.)
You are upgrading your 6-node NetApp ONTAP cluster from ONTAP 9.9.1 to 9.16.1. As part of the ONTAP software upgrade process, you need to update the cluster switches. After you update the first switch, you receive the following AutoSupport message:
Exhibit — AutoSupport Alert
vifmgr: callhome.clus.net.degraded:alert:
Call home for CLUSTER NETWORK DEGRADED:
Large MTU Packet Loss - Ping failures detected
between Node1_clus1 (169.254.2.94) on Node1
and Node2_clus2 (169.254.248.67) on Node2.
All cluster ports and interfaces are in an up/up status.
What is causing this error?
You have replaced the cluster backend switches on a 4-node NetApp ONTAP cluster with new switches. After the replacement, you realize that the system shows errors for the old switches that were removed:

You also notice that system switch ethernet show shows four switches, the two old switches and the two new switches.
What action will resolve the issue?
Which two commands confirm whether an aggregate is WAFL inconsistent? (Choose two.)
When you add a new disk to an ONTAP 9.1 system, you see an error that the disk “has raid label with version (16), which is not within the currently supported range (14-15).” What is one possible cause of this error?
You have upgraded your cluster from ONTAP 9.5 software to ONTAP 9.7 software. After the upgrade, you notice that the upgrade causes issues. You decide to revert to ONTAP 9.5 software.
Which revert step is allowed?
Which two tools can be used to recover an inconsistent aggregate? (Choose two.)
Which type of core file is generated when a node panics?
A new NetApp NS224 disk shelf is correctly cabled to a NetApp AFF HA pair. The disks show up as single-path.
Which action corrects the issue?
In maintenance mode, which of the following commands shows disk ownership?
In which two sections of AutoSupport can you find information to analyze the following panic? (Choose two.)
Panic_Message: PCI Error NMI from device(s):ErrSrcID(CorrSrc(0xf00),UCorrSrc(0x18)), RPT(0,3,0):Qlogic FC 16G adapter in slot 1 on Controller
During an ONTAP upgrade, nodeA1 fails to boot. You notice that it is loading the previous version of ONTAP software. What step can be taken to boot the node successfully?
In a SAS stack of shelves, what is the topology of the connection between expander and disk?
A 4-node NetApp ONTAP cluster sent an alert that one of the cluster interconnect switches has failed. After replacement, the system administrator notices that half of the cluster LIFs are not on their home ports.
Which parameter must the system administrator enable to automatically migrate the cluster LIFs?
What are the two steps to unfail a disk in maintenance mode? (Choose two.)
You have identified that the file named quarterly_25.docx is inconsistent.
Which nodeshell command reports whether there are Snapshot copies available?
Which two tools can you use to invoke AutoSupport? (Choose two.)
A node has panicked with a PCI/NMI error. Giveback has not been performed.
Which two commands should you run to collect the logs to determine the cause? (Choose two.)
You have replaced a failed boot device. You perform boot_recovery and receive no errors. However, when the node reboots, it reports that it has no disks.
What are two possible causes? (Choose two.)
You receive the following AutoSupport message:
[Node-01: cshmd: hm.alert.raised:alert]:
Alert Id = ClusterSwitchConnectivity_Alert
Alerting Resource = Node-02
raised by monitor ethernet-switch
[Node-01: mgwd: callhome.hm.alert.major:alert]:
Call home for Health Monitor process cshm:
ClusterSwitchConnectivity_Alert[Node-02].
[Node-01: mgwd: callhome.hm.alert.major:alert]:
Call home for Health Monitor process cshm:
ClusterSwitchConnectivity_Alert[Node-02].
When researching, you discover the following output:
Exhibit 2 — Network Port Health
Cluster::* > network port show
-health-status degraded
-fields health-degraded-reasons
node port health-degraded-reasons
-------- ---- -----------------------
Node-02 e0a link_flapping
What action do you take to resolve this issue?
A node has failed.
Which two conditions must be met for an automatic takeover to be triggered? (Choose two.)