Juniper JN0-335 Exam With Confidence Using Practice Dumps

• Cluster failovers occur when one node in a chassis cluster becomes inactive or unreachable, and the other node takes over the processing of traffic and services. To control when cluster failovers occur, you can configure two specific parameters on an SRX Series device: heartbeat-interval and heartbeat-threshold12.
• Heartbeat-interval is the time interval, in milliseconds, between heartbeat messages sent by each node to the other node. The default value is 1000 ms. You can configure the heartbeat-interval value from 100 through 3000 ms1.
• Heartbeat-threshold is the number of consecutive heartbeat messages that can be missed before a node is considered to be down. The default value is 3. You can configure the heartbeat-threshold value from 2 through 2551.
• The combination of heartbeat-interval and heartbeat-threshold determines the failover time, which is the maximum time it takes for a node to detect the failure of the other node and initiate a failover. The failover time is calculated as follows: failover time = heartbeat-interval x heartbeat-threshold1.
• For example, if the heartbeat-interval is 1000 ms and the heartbeat-threshold is 3, the failover time is 3000 ms. This means that if a node does not receive three consecutive heartbeat messages from the other node within 3000 ms, it will assume that the other node is down and initiate a failover1.
• You can configure the heartbeat-interval and heartbeat-threshold parameters using the set chassis cluster redundancy-group group-id node node-id priority priority heartbeat-interval interval heartbeat-threshold threshold command1.

References:

• 1: Configuring Chassis Cluster Redundancy Group Properties | Junos OS | Juniper Networks
• 2: Example: Configuring an Active/Passive Cluster Deployment | Junos OS | Juniper Networks

 To create a security policy that will automatically add infected hosts to the infected hosts feed and block further communication through the SRX Series device, you need to add a security intelligence policy to the permit portion of the security policy. A security intelligence policy is a set of rules that defines the actions to be taken for traffic thatmatches a specific category of threat feeds, such as infected hosts, command and control servers, or botnets. By adding a security intelligence policy to the permit portion of the security policy, you can enable the SRX Series device to dynamically update the infected hosts feed based on the advanced anti-malware policy results, and block the traffic from or to the infected hosts. Options B, C, and D are not correct because they do not enable the automatic addition of infected hosts to the feed or the blocking of their communication. References: The answer can be verified from Juniper’s official documentation on security intelligence and advanced anti-malware available on their website. Here are some relevant links:

• Security Intelligence Feature Guide for Security Devices
• Advanced Anti-Malware Feature Guide for Security Devices
• Configuring Security Intelligence Policy on the SRX Series Device
• [Configuring Advanced Anti-Malware Policy on the SRX Series Device]

 The show security policies policy-name detail command shows policy counters for a configured policy. Policy counters display the number of packets and bytes that match the policy, as well as the number of sessions that are created, denied, or closed by the policy. Policy counters can help monitor and troubleshoot the traffic flow and security policy enforcement on the SRX firewall1.

The show security policies policy-name detail command does not display details about the default security policy, which is the implicit policy that is applied when no other policy matches the traffic. The default security policy can be viewed by using the show security policies default-policy command2.

The show security policies policy-name detail command does not identify the different custom policies enabled, which are the user-defined policies that specify the action and conditions for the traffic between zones. The custom policies can be viewed by using the show security policies command without any options1.

The show security policies policy-name detail command does not show the system log files for the local SRX Series device, which are the files that record the events and messages generated by the device. The system log files can be viewed by using the show log command with the name of the file3. References:

• 1: show security policies | Junos OS | Juniper Networks
• 2: Understanding Default Security Policies | Junos OS | Juniper Networks
• 3: show log | Junos OS | Juniper Networks