MikroTik MTCNA - MikroTik Training MTCNA New Questions

MikroTik RouterOS supports running multiple dynamic routing protocols simultaneously, including RIP, OSPF, and BGP. They are independent processes and can be configured in parallel. This is commonly used in complex network environments or during routing migrations.

A.✔FALSE – You can run OSPF and RIP at the same time.

B.✘TRUE – Incorrect; both protocols are fully supported to coexist.

Extract from MTCNA Course Material – Dynamic Routing:

“RouterOS supports multiple dynamic routing protocols, including simultaneous use of RIP and OSPF.”

Extract from René Meneses Study Guide – Routing Protocols:

“You can configure both RIP and OSPF to run at the same time on a single router.”

Extract from MikroTik Wiki – Routing Overview:

“RouterOS allows multiple routing protocols to operate concurrently.”

===========

Setting "forwarding=no" on a wireless interface prevents communication between connected clients on that interface and between that interface and other interfaces in the same bridge. This means:

Stations connected to wlan1 cannot talk to each other

Stations on wlan1 cannot talk to stations on wlan2 (even if bridged)

Stations on wlan2 can talk to each other normally

Evaluation:

A.✅Correct – forwarding=no does not affect wlan2

B.❌Incorrect – forwarding=no blocks this

C.✅Correct – clients on wlan1 cannot talk to each other either

D.❌Bridge filters can be used but this scenario is about forwarding settings

E.❌Blocked by forwarding=no

MTCNA Wireless Module – Wireless Forwarding Behavior:

“Forwarding=no disables client-to-client communication on the interface and across bridges.”

René Meneses Study Guide – Wireless Access Config:

“Use forwarding=no to isolate clients on the same AP. Affects bridging too.”

Terry Combs Notes – Wireless Isolation:

“Setting forwarding=no isolates all clients on that wireless card.”

Answer: A, CQUESTION NO: 81 [Wireless]

Consider a wireless access point with mode=ap-bridge. What is the maximum number of concurrent clients that can connect to it?

A. 2007

B. 2012

C. 2048

D. 1024

Answer: C

In MikroTik RouterOS, the theoretical maximum number of clients that can associate with an AP in ap-bridge mode is 2048. However, practical limits depend on hardware performance and network stability, and most real-world setups use far fewer clients.

Let’s review:

A. 2007 →❌Close, but not the actual hard limit

B. 2012 →❌Incorrect

C.✅2048 → Correct per MikroTik’s AP mode specification

D. 1024 →❌Lower than the actual maximum

MTCNA Wireless Module – AP Behavior:

“In ap-bridge mode, the maximum theoretical client limit is 2048. Actual stable operation may be lower.”

René Meneses Guide – Wireless Scaling:

“2048 is the upper limit for client associations on a MikroTik AP in bridge mode.”

Terry Combs Notes – Client Capacity:

“2048 clients = maximum. Performance may degrade before that in high-traffic environments.”

TTL (Time to Live) is a field in the IP header that limits the number of hops a packet can travel. Each router that processes the packet decrements the TTL by 1. When TTL reaches 0, the packet is dropped.

Default TTL values vary by operating system, but in RouterOS and many Linux-based systems, the default TTL is 64.

A. 60 → Incorrect, used in some systems but not the MikroTik default

B. 30 → Incorrect

C. 1 → Incorrect; would allow only one hop

D. 64 →✔Correct

Extract from Official MTCNA Course Material – TTL Field Explanation:

"The default TTL in RouterOS and most Unix-like systems is 64. Each router decrements this by 1 until the packet is discarded."

Extract from René Meneses Study Guide – IP Protocol Details:

“TTL is initialized to 64 by default in MikroTik RouterOS.”

Extract from MikroTik Wiki – IP Protocol Section:

"RouterOS sets default TTL of 64 unless manually configured otherwise."

===========

PPPoE (Point-to-Point Protocol over Ethernet) does not natively support encryption. It provides authentication using PAP/CHAP and allows IP assignment, but any data transmitted through a PPPoE tunnel is unencrypted unless another encryption mechanism (such as IPSec) is used on top of it.

MikroTik RouterOS supports encrypted tunneling protocols such as SSTP, L2TP/IPSec, or OpenVPN, but not native encryption in PPPoE.

MTCNA Course Manual – PPP Protocols Overview:

“PPPoE supports user authentication and compression but not encryption by itself.”

René Meneses Study Guide – Tunneling Protocols:

“PPPoE is not secure by design. If encryption is needed, use SSTP or L2TP/IPSec.”

Terry Combs Notes – PPP Protocol Capabilities:

“PPPoE does not encrypt data. Only authentication is handled within PPP.”

Answer: BQUESTION NO: 36 [Wireless]

Why is it useful to set a Radio Name on the radio interface?

A. To identify a station in the Access List

B. To identify a station in Neighbor discovery

C. To identify a station in a list of connected clients

Answer: C

Setting a Radio Name in RouterOS provides a unique identifier that is visible to other devices in the wireless environment. It is particularly helpful for identifying connected clients in the registration table on the Access Point.

This name does not affect Access List matching or general Layer 2 communication — it’s used for human readability and monitoring.

A. Access List uses MAC addresses for filtering →❌

B. Neighbor discovery identifies devices based on MAC, IP, and identity →❌

C. Correct → Radio Name shows up in the registration table and helps identify stations✅

MTCNA Wireless Module – Interface Settings:

“The Radio Name is shown in the registration table of access points, making it easier to identify connected clients.”

René Meneses Guide – Wireless Management Tips:

“Use Radio Names to label devices in multi-client setups. It appears under registration when clients connect.”

Terry Combs Notes – Wireless Interface Options:

“Radio Name is not used for access filtering — it’s for display and diagnostics.”

Answer: CQUESTION NO: 37 [DHCP]

A DHCP server is configured on a LAN interface which is a port on a bridge. The DHCP server does not start. What could be the reason(s)?

A. The DHCP server cannot run on an interface which is also a bridge port

B. There might not be an IP address assigned to the LAN Interface

C. The IP address pool could be incorrectly defined

D. There may be multiple IP addresses set on the LAN interface

Answer: B, C

For a DHCP server to operate properly, the following conditions must be met:

The DHCP server must be attached to the correct interface (typically the bridge, not individual ports).

The bridge interface must have a valid IP address.

The IP address pool must be defined correctly (matching subnet, avoiding conflicts).

Let’s evaluate:

A.❌Incorrect. DHCP can run on a bridge or an interface on a bridge. It is recommended to attach DHCP to the bridge, not individual ports.

B.✅Correct. If there is no IP address on the interface (bridge), DHCP won’t start.

C.✅Correct. If the address pool is misconfigured (e.g., outside the subnet or overlapping with the router’s IP), DHCP won’t function.

D.❌Not a valid blocker. Multiple IPs can exist on the interface; DHCP still works if one is valid.

MTCNA DHCP Module – Configuration Troubleshooting:

“Make sure that the interface (bridge) where the DHCP server is assigned has a valid IP and a properly defined pool.”

René Meneses Guide – DHCP Server Setup:

“DHCP will not function if no IP is assigned to the interface. Check the pool range and binding address.”

Terry Combs Notes – DHCP Tips:

“Assign the DHCP server to the bridge, not individual ports. Missing IP or incorrect pool = DHCP won’t start.”

Answer: B, CQUESTION NO: 38 [PPP]

There can be more than one PPPoE server in a single broadcast domain:

A. True

B. False

Answer: A

Yes, it is possible — and fully supported — to run multiple PPPoE servers in the same Layer 2 broadcast domain. Clients will receive Offer packets (PADO) from all PPPoE servers, and can choose which one to connect to based on configuration or server name (service name).

This is commonly used in ISP networks to provide redundancy or offer different service types.

MTCNA Course Manual – PPPoE Deployment:

“Multiple PPPoE servers may exist in the same Layer 2 domain. Clients choose based on response or service name.”

René Meneses Study Guide – PPPoE Operations:

“PPPoE discovery protocol supports multi-server environments. Clients may be configured to select a preferred one.”

Terry Combs Notes – PPPoE Server Design:

“Several PPPoE servers can coexist. Just avoid assigning overlapping IP pools.”