Complete H12-891_V1.0 Huawei Materials

Virtual Networks in Huawei CloudCampus Solution:

Virtual networks (VNs) are segmented based on services (e.g., IoT, Guest Wi-Fi, Enterprise Wi-Fi).

Each VN has its own routing and forwarding instance (VRF).

Isolation Between Virtual Networks:

By default, different virtual networks are isolated.

If inter-VN communication is required, it must be manually configured using policy-based routing (PBR), inter-VRF routing, or firewall policies.

Reference from Huawei HCIE-Datacom Documentation:

Huawei CloudCampus Solution Guide – Virtual Networks and Segmentation

HCIE-Datacom Training Material – Policy-Based Inter-VN Communication

An IPsec Security Association (SA) includes the following critical components:

SPI (Security Parameter Index)

Destination IP address

Security Protocol (AH or ESP)

Encryption/Authentication algorithms

The Source IP address is not a defining parameter of an SA. SA is unidirectional and identified based on the SPI and destination address.

Exact Extract - Huawei Security Configuration Guide – IPsec Fundamentals:

“An SA is uniquely identified by the SPI, destination IP, and security protocol. The source address is not a determining factor in the SA.”

Forwarding Equivalence Class (FEC) is a key concept in MPLS (Multiprotocol Label Switching), where packets with the same forwarding characteristics are grouped into an FEC and assigned a label.

Correct Answers (Cannot be Used for FEC Allocation):

A. Fragment Offset – Incorrect as an FEC allocation standard

Fragment offset is used for reassembling fragmented IP packets at the receiver side.

It is not relevant for MPLS label assignment.

B. Application Protocol – Incorrect as an FEC allocation standard

MPLS does not classify packets based on application-layer protocols (e.g., HTTP, FTP).

It works mainly at Layer 2 and Layer 3.

Incorrect Answers (Valid FEC Allocation Standards):

C. Destination Address – Valid FEC allocation criterion

One of the most common MPLS FEC classifications.

Packets with the same destination are grouped into the same FEC.

D. Class of Service (CoS) – Valid FEC allocation criterion

MPLS uses CoS-based traffic classification (e.g., Exp bits in MPLS headers).

Different CoS levels can be mapped to different labels.

Reference from Huawei HCIE-Datacom Documentation:

Huawei MPLS Technology Guide – FEC and Label Assignment

HCIE-Datacom MPLS VPN Configuration Guide

In OSPFv3, Link-LSA (Type 8) is generated by a router for each of its interfaces to advertise:

The router ' s link-local address on that interface.

The IPv6 prefixes associated with the interface.

Flags and options, such as router priority or loopback indicators.

From the output:

Link-LSA (Interface GigabitEthernet0/0/0)

Originating Router: 10.1.2.2

Link-Local Address: FE80::2E0:FCFF:FECD:4F79

Prefix: 2001:DB8:2345:23::/64

A. The link-local address of R2’s GE0/0/0 is FE80::2E0:FCFF:FECD:4F79→ This matches the Link-Local Address field in the LSA. ✅

B. The IPv6 address prefix of R2’s GE0/0/0 is 2001:DB8:2345:23::/64→ This matches the Prefix field in the LSA. ✅

C. This LSA indicates that R2 does not support external routes but can participate in IPv6 route calculation→ ❌ Incorrect.

The Link-LSA does not provide any indication about external route capabilities.

It simply advertises interface-specific IPv6 and link-local info.

Whether R2 supports external routes depends on Type 5 (External) or Type 7 (NSSA) LSAs, not Link-LSAs.

D. This LSA is generated by R2→ The Originating Router: 10.1.2.2 is R2’s router ID, so this LSA is definitely generated by R2. ✅

Correct Answers: A, B, D

The Link-LSA in OSPFv3 contains:

The link-local address used by the originating router on the link.

A list of all IPv6 prefixes associated with the link.

Flags such as router priority and the Router-LSA options.

These LSAs are always generated by the router itself and are not flooded beyond the link.