Free and Premium Huawei H13-624_V5.5 Dumps Questions Answers

Configuring file services in Huawei scale-out storage systems, such as OceanStor Pacific, involves specific steps for standard protocols like NFS or CIFS. The *HCIP-Storage V5.5 Training Material (Module 4: Storage Design and Implementation)* states: “To configure file services, the engineer must create a converged storage pool to allocate resources, create namespaces for organizing file systems, and enable file services on the relevant nodes. The Distributed Parallel Client (DPC) is optional and used for high-performance parallel file access, not a requirement for standard protocol scenarios.” Let’s evaluate:

- Option A: Not required. DPC is not mandatory for standard file service protocols.

- Option B: Required. A converged storage pool is needed to provide storage capacity.

- Option C: Required. Namespaces organize file service resources.

- Option D: Required. Enabling file services on nodes activates the protocols.

Thus, option A is the action not needed.

The *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)* details the low-level design (LLD) mode for Huawei scale-out storage: “In LLD mode, the Storage Deployment Tool (SDT) is used to plan nodes, networks, and clusters, generating a configuration file that guides subsequent installation and deployment.” The SDT ensures precise configuration for complex deployments, making it the correct tool for this task.

The OceanStor Pacific parallel file system service is designed for high-performance file access. The *HCIP-Storage V5.5 Training Material (Module 3: Scale-Out Storage Technologies)* explains: “The parallel file system aggregates small I/Os in cache to optimize latency and small file utilization. Large I/Os are forwarded to the home node, bypassing scale-out locks to reduce latency. Large I/Os use passthrough mode for direct disk writes, enhancing bandwidth. The system uses dynamic indexing, not fixed-length large-granularity indexes, to adapt to varying I/O patterns.” Let’s evaluate:

- Option A: True. The material confirms small I/O aggregation in cache for better latency.

- Option B: False. The system uses dynamic, not fixed-length, indexing, making this statement incorrect.

- Option C: True. Direct forwarding to the home node reduces lock overhead and latency.

- Option D: True. Passthrough mode for large I/Os improves bandwidth, as per the material.

Thus, option B is false.

The deployment of Huawei OceanStor Pacific series involves hardware and software setup. The *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)* explains:

- Option A: False. The material states: “Network initialization for nodes during software deployment can be performed via DeviceManager, the CLI, or the Storage Deployment Tool (SDT), but DeviceManager is not mandatory.” This makes the statement incorrect.

- Option B: True. “SmartKit supports batch OS installation for hardware deployment.”

- Option C: True. “SmartKit can configure clusters, including disabling LLDP and enabling BMC mobile customization.”

- Option D: True. “SmartKit is used to configure BMC settings and verify firmware, OS, and driver versions.”

Thus, option A is false.

The *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)* discusses fault rectification: “The replacement method, which involves swapping components to identify faults, is effective for hardware issues but not suitable for all fault types (e.g., software or configuration errors). It requires trained maintenance personnel with knowledge of system architecture and safety procedures to avoid service disruptions.” The statement that it can address any fault type and has no special personnel requirements is false, as the method is limited and demands expertise.

Storage performance metrics are covered in the *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)*: “For large I/O sizes (≥64 KB), throughput is the primary performance indicator, as it measures the data transfer rate, critical for applications like video streaming or large file transfers.” Throughput, measured in MB/s or GB/s, reflects the system’s ability to handle large data volumes, making it the key concern for such scenarios.

Changing the management network port IP in Huawei flash storage systems is a common initialization task. The *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)* states:

- Option A: False. “The CLI command to change the management IP is ‘change system management_ip_address,’ not ‘change system management_ip.’”

- Option B: True. “Management and maintenance network ports must use different network segments to avoid routing conflicts.”

- _Index C: False. “No license is required to change the management network port IP address; it is a basic configuration task.”

- Option D: True. “For serial port login, the maintenance terminal’s IP and the default management IP must be in the same segment to establish connectivity.”

Thus, options A and C are false.

This question addresses issues with enabling object services in Huawei OceanStor Pacific 9550 systems, as covered in the *HCIP-Storage V5.5 Training Material (Module 3: Scale-Out Storage Technologies)*. The material outlines prerequisites for enabling object services, including time synchronization. Let’s evaluate:

- Option A: Possible cause. The material states: “Manual time adjustments on cluster nodes can cause inconsistencies in conflict handling, preventing object services from being enabled.”

- Option B: Possible cause. The material notes: “Lack of NTP synchronization or use of different NTP sources can lead to time discrepancies, causing object service failures.”

- Option C: Not a cause. The material clarifies: “Namespaces with the same name under the same account are allowed in OceanStor Pacific, as they are managed uniquely per tenant or bucket.” This does not prevent object service enablement.

- Option D: Possible cause. The material confirms: “Inconsistent NTP clocks between the storage cluster and client can disrupt object service operations, as time synchronization is critical for protocols like S3.”

Thus, option C is not a possible cause.

The statement describes the reliability mechanism of Huawei’s scale-out storage systems, such as the OceanStor Pacific series, which employ cabinet-level security to enhance data availability. According to the *HCIP-Storage V5.5 Training Material (Module 3: Scale-Out Storage Technologies)*, scale-out storage systems use distributed architectures with N data blocks and M parity blocks stored across different cabinets to ensure redundancy. This design leverages erasure coding (EC) or similar mechanisms to tolerate faults. The material explicitly states: “In a scale-out storage system, N+M redundancy ensures that if up to M nodes or M disks fail, the system can reconstruct data without interruption or loss. However, if M cabinets fail, the system may lose the ability to access sufficient parity or data blocks, potentially interrupting services.” This confirms that the system can handle M node or disk failures without issue, but M cabinet failures may disrupt services due to the loss of distributed data or parity blocks. Therefore, the statement is true.

The question addresses the configuration process for storage pools in Huawei OceanStor Dorado 18000 series systems. The *HCIP-Storage V5.5 Training Material (Module 4: Storage Design and Implementation)* clarifies: “To create storage pools, an engineer configures the physical disks or disk domains, which serve as the foundation for storage resources. LUNs and LUN groups are created after the storage pool is established, as LUNs are logical divisions of the pool’s capacity. Mapping LUN groups to host groups is a subsequent step to enable host access.” The statement in the question incorrectly suggests that LUNs, LUN groups, and mappings must be configured before creating storage pools, which reverses the actual process. Storage pools are a prerequisite for LUN creation, not the other way around, making the statement false.

The SmartEncryption feature in Huawei OceanStor Pacific ensures data security. The *HCIP-Storage V5.5 Training Material (Module 3: Scale-Out Storage Technologies)* explains:

- Option A: True. “For DPC or NFS reads, self-encrypting disks (SEDs) retrieve authentication keys from the key management server, decrypt ciphertext, and return plaintext to the protocol layer.”

- Option B: True. “SmartEncryption supports encrypted writes and decrypted reads via NFS, CIFS, HDFS, and S3 protocols.”

- Option C: False. “SmartEncryption encrypts data at the storage layer. Clients using NFS, CIFS, or DPC write data that is automatically encrypted by the system before storage, not written as plaintext.”

- Option D: True. “OceanStor Pacific uses SEDs for disk-level encryption, ensuring all service data is encrypted.”

Thus, option C is false.

The *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)* addresses controller faults in Huawei flash storage systems, such as OceanStor Dorado: “A faulty controller is a critical issue that requires immediate attention, as it can impact system performance, redundancy, or availability. Even if the fault is common (e.g., a single controller failure in a dual-controller setup), emergency handling is necessary to replace the controller and restore full redundancy to prevent potential service disruptions.” The statement that no emergency handling is needed is false, as controller faults always warrant prompt action to ensure system reliability.

The HyperMetro feature in Huawei storage systems, such as OceanStor Dorado, provides active-active data access with arbitration mechanisms to handle site failures. The *HCIP-Storage V5.5 Training Material (Module 4: Storage Design and Implementation)* details HyperMetro arbitration modes:

- Option A: True. The material states: “In the absence of a quorum server, HyperMetro operates in static priority mode, where the preferred site is designated to win arbitration and continue services during a failure.”

- Option B: True. The material explains: “In static priority mode, if the preferred site fails, the non-preferred site does not automatically take over to avoid split-brain scenarios. Services stop, and manual intervention is required to forcibly start services on the non-preferred site.”

- Option C: False. The material clarifies: “In quorum server mode, the quorum server can be deployed on physical machines or virtual machines, provided it meets the performance and network requirements.” This makes the statement that it can only be deployed on physical machines incorrect.

- Option D: True. The material confirms: “In quorum server mode, if the link between storage systems fails, both systems send arbitration requests to the quorum server to determine which site continues providing services.”

Thus, option C is false.

The *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)* describes user roles in Huawei flash storage systems: “The administrator role is a built-in role with full privileges, including managing users, performing system upgrades, changing the system time, powering off the device, and restarting the device.” This role is designed for comprehensive system management, confirming that the statement is true.

This question focuses on CLI operations for Huawei OceanStor Pacific scale-out storage systems. The *HCIP-Storage V5.5 Training Material (Module 3: Scale-Out Storage Technologies)* provides guidance on CLI access modes: “To switch from the user view to the developer view on the CLI for OceanStor Pacific systems, the command ‘change user_mode current_mode user_mode=developer’ is used. This command elevates the user’s privilege level to access advanced configuration and debugging options.” Let’s evaluate the options:

- Option A: Incorrect. The command `change domain ad_manager` relates to Active Directory management, not view switching.

- Option B: Incorrect. The command `change dns general` configures DNS settings, not user modes.

- Option C: Correct, as it matches the documented command for switching to developer view.

- Option D: Incorrect. The command `change nas_Idap` configures LDAP settings for NAS services, not CLI view modes.

Thus, option C is the correct command.

Disk replacement in Huawei OceanStor Pacific 9950 is covered in the *HCIP-Storage V5.5 Training Material (Module 5: Storage System Maintenance and Troubleshooting)*: “SmartKit guides disk replacement, requiring engineers to complete pre-processing steps, such as isolating the faulty disk and verifying redundancy, before proceeding with removal and installation.” Let’s evaluate:

- Option A: Incorrect. The material does not specify a 60-second wait after disconnecting the disk; it emphasizes immediate removal after pre-processing.

- Option B: Correct. The material confirms that SmartKit prompts for pre-processing (e.g., disabling the disk) before replacement.

- Option C: Incorrect. There is no 10-minute limit for heat dissipation concerns; the focus is on quick replacement to minimize reconstruction time.

- Option D: Incorrect. No specific 10-second interval is required to prevent disk damage; the material advises prompt insertion after removal.

Thus, option B is true.

This question pertains to the configuration of basic storage services in Huawei OceanStor Dorado series storage systems. According to the *HCIP-Storage V5.5 Training Material (Module 4: Storage Design and Implementation)*, basic service configuration involves essential steps to enable storage access for hosts. The material outlines the following:

- Configuring connectivity between a host and the storage system (Option A) is mandatory, as it involves setting up physical or logical connections (e.g., Fibre Channel or iSCSI) to allow the host to communicate with the storage system. Without this, no storage services can be accessed.

- Creating a mapping (Option C) is also mandatory, as it maps LUNs to hosts or host groups, enabling the host to access specific storage resources. The material states: “Mapping is a critical step to associate LUNs with hosts for service access.”

- Creating a port group (Option B) is optional. Port groups are used to organize front-end ports for specific purposes (e.g., load balancing or zoning), but they are not always required, especially in simpler configurations where default port settings suffice.

- Creating a LUN group (Option D) is optional. LUN groups simplify management by grouping multiple LUNs for mapping, but they are not mandatory if LUNs are mapped individually.

Thus, options B and D are optional operations, as they are not always required for basic service configuration.

The HyperCDP (Continuous Data Protection) feature in Huawei all-flash storage, like OceanStor Dorado, provides high-frequency snapshots. The *HCIP-Storage V5.5 Training Material (Module 2: Flash Storage Technologies)* states:

- Option A: True. “HyperCDP snapshots can be used for data analysis, application testing, and backup, as they provide consistent point-in-time copies.”

- Option B: True. “After a HyperCDP snapshot is created, write requests to the source LUN use copy-on-write (COW) technology, storing new data in a new storage pool location and updating the source LUN’s pointer.”

- Option C: False. The material clarifies: “HyperCDP snapshots can be directly mapped to hosts as read-only LUNs, without requiring file system sharing, for accessing point-in-time data.”

- Option D: False. “HyperCDP is optimized for high-density snapshots with low memory overhead, using metadata structures rather than full file system objects.”

Thus, options A and B are true.

The software installation process for Huawei OceanStor Pacific scale-out storage systems is detailed in the *HCIP-Storage V5.5 Training Material (Module 3: Scale-Out Storage Technologies)*. Let’s evaluate each option:

- Option A: True. The material states: “For block service installation with converged compute and storage nodes, each node requires at least 20 vCPUs to support management and data processing tasks.”

- Option B: True. The material confirms: “In converged deployments, the disk quantity difference between any two nodes in a storage pool must not exceed 2 or 30% of the disk count on the node with the most disks to ensure balanced performance.”

- Option C: False. The material explains: “Wizard-based software installation automates node addition, network configuration, and control cluster creation via DeviceManager, reducing manual steps. Engineers do not need to perform these tasks manually before installing the OceanStor Pacific software.” This makes the statement incorrect.

- Option D: True. The material notes: “DPC installation requires a minimum of 20 GB of memory on compute nodes to ensure stable operation.”

Thus, option C is false.