CWNP CWAP-404 Dumps

The 4-way handshake is the process that establishes the pairwise transient key (PTK) between the client and the AP in WPA2-PSK. The PTK is derived from the PSK, the SSID, and some random numbers exchanged in the handshake frames. The PTK is used to encrypt and decrypt the data frames between the client and the AP. Therefore, in order to decrypt WPA2-PSK data packets, a protocol analyzer needs to capture the 4-way handshake frames and have the PSK and SSID configured in the analyzer software12 References:

• CWAP-404 Study Guide, Chapter 3: 802.11 MAC Layer Frame Formats and Technologies, page 87
• CWAP-404 Objectives, Section 3.5: Analyze security exchanges

The statement that the Frame Control field contains subfields, and some 1-bit flags is true. The Frame Control field is a 2-byte field in the MAC header that contains information about the type, subtype, and characteristics of a frame. The Frame Control field is divided into several subfields, each with a specific function and length. Some of these subfields are 1-bit flags, which can be set to 0 or 1 to indicate a certain condition or status. For example, the To DS and From DS subfields are 1-bit flags that indicate whether a frame is destined for or originated from the DS (Distribution System). The other statements are not true, as they do not describe the Frame Control field correctly. All types of frames (management, control, and data) have a Frame Control field, not just control frames. The Frame Control field is not used to communicate the duration value, which is a separate field in the MAC header. The Frame Control field is not always set to 0, as it varies depending on the type, subtype, and characteristics of each frame. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 113-114

The To DS and From DS flags should be set to 0 in an Association Response frame. An Association Response frame is a type of management frame that is transmitted by an AP to accept or reject an association request from a STA. The To DS (To Distribution System) and From DS (From Distribution System) flags are two bits in the Frame Control field of the MAC header that indicate whether a frame is destined for or originated from the DS (Distribution System), which is a system that connects multiple BSSs together. The To DS and From DS flags can have four possible combinations: 00, 01, 10, or 11. For an Association Response frame, which is sent from an AP to a STA within a BSS, both flags should be set to 0. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 121-122

The most likely issue that can be identified from the spectrum analysis is a power mismatch between the APs and the clients. A power mismatch occurs when the APs transmit at a higher power level than the clients, or vice versa. This can cause asymmetric communication, where one side can hear the other, but not vice versa. This can result in poor performance, disconnections, or packet loss. A spectrum analysis can reveal a power mismatch by showing different signal amplitudes or RSSI values for the APs and the clients on the same channel or frequency. The other options are not correct, as they cannot be identified from the spectrum analysis alone. The tablets’ SSID, power save mode, and noise floor can be determined by using other tools or methods, such as protocol analysis, site survey, or device configuration. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 79-80

One of the information that is communicated by bits in the PHY header is data rate. Data rate is the speed at which data is transmitted or received over the wireless medium. Data rate depends on factors such as modulation, coding, channel width, spatial streams, and guard interval. Data rate is indicated by bits in different fields of the PHY header, depending on the type of PPDU (e.g., OFDM, HT, VHT, HE). The receiver uses these bits to determine how to decode and demodulate the rest of the PPDU. The other options are not correct, as they are not communicated by bits in the PHY header. SNR (Signal-to-Noise Ratio), noise, and signal strengthare measured by the receiver based on its own capabilities and environment. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 101-105

The value of the Listen Interval field in an Association Request frame indicates how often a STA in power save mode wakes up to listen to Beacon frames. The Listen Interval is expressed in units of Beacon Intervals (typically 100 TU or 102.4 ms). For example, if the Listen Interval is set to 10, it means that the STA will wake up every 10 Beacon Intervals (or about 1 second) to check for buffered frames at the AP. The Listen Interval is used by the AP to determine how long it can hold frames for a STA in power save mode before discarding them . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 197; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 198.

One way to confirm if you have missing packets in your packet capture is to look for gaps in the sequence number in MAC headers. The sequence number is a 12-bit field in the MAC header that is used to identify and order data frames within a traffic stream. The sequence number is incremented by one for each new data frame transmitted by a STA, except for retransmissions, fragments, and control frames. The sequence number can range from 0 to 4095, and then wraps around to 0. If you see a jump or a gap in the sequence number between two consecutive data frames from the same STA, it means that you have missed some packets in between. The other options are not correct, as they do not confirm if you have missing packets in your packet capture. CRC errored packets are packets that have been corrupted during transmission and have failed the error detection check. Protocol analyzers may show the number of CRC errored packets in their statistics view, but not the number of missing packets. Retransmissions are an indication of packet loss or collision, but not necessarily of missing packets in your capture. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 114-115

A hexadecimal value is a value that uses base 16 notation, which means it can have digits from 0 to 9 and letters from A to F. A hexadecimal value is usually preceded by 0x to indicate that it is hexadecimal and not decimal or binary. For example, 0x0A is hexadecimal for 10 in decimal or 00001010 in binary. The other options are not valid prefixes for hexadecimal values.References:

• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 35
• CWAP-404 Objectives, Section 2.2: Analyze field values

The CRC is calculated over the MAC Header and Frame Body only. The CRC (Cyclic Redundancy Check) is a 32-bit value that is used for error detection in wireless transmissions. The CRC is calculated over the MAC Header and Frame Body of a PSDU, which are the parts of the data unit that contain information such as source and destination addresses, frame type, frame control, sequence number, payload, etc. The CRC is appended to the end of the PSDU as a FCS (Frame Check Sequence) field. The CRC is not calculated over the PHY Header or PHY Preamble, which are parts of the PPDU that contain information such as modulation, coding, data rate, etc. The PHY Header and PHY Preamble are added or removed by the PHY layer during the conversion between PSDU and PPDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

 The GTK (Group Temporal Key) is encrypted within the third message of the 4-Way Handshake. The 4-Way Handshake is a process that establishes a secure connection between a STA (station) and an AP (access point) using WPA2 (Wi-Fi Protected Access 2), which is a security protocol that uses AES-CCMP (Advanced Encryption Standard-Counter Mode CBC-MAC Protocol) as its encryption algorithm. The 4-Way Handshake consists of four messages that are exchanged between the STA and the AP. The first message is sent by the AP to the STA, containing the ANonce (Authenticator Nonce), which is a random number generated by the AP. The second message is sent by the STA to the AP, containing the SNonce (Supplicant Nonce), which is a random number generated by the STA, and the MIC (Message Integrity Code), which is a value that verifies the integrity of the message. The third message is sent by the AP to the STA, containing the GTK, which is a key that is used to encrypt and decrypt multicast and broadcast data frames, and the MIC. The GTK is encrypted with the KEK (Key Encryption Key), which is derived from the PTK (Pairwise Temporal Key). The PTK is a key that is used to encrypt and decrypt unicast data frames, and it is derived from the PMK (Pairwise Master Key), the ANonce, and the SNonce. The fourth message is sent by the STA to the AP, containing only the MIC, to confirm the completion of the 4-Way Handshake. The other options are not correct, asthey are not encrypted within the third message of the 4-Way Handshake. The PMK is a key that is derived from a passphrase or obtained from an authentication server, and it is not transmitted in any message of the 4-Way Handshake. The PTK is a key that is derived from the PMK, the ANonce, and the SNonce, and it is not transmitted in any message of the 4-Way Handshake. The GMK (Group Master Key) is a key that is generated by the AP and used to derive the GTK, and it is not transmitted in any message of the 4-Way Handshake. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 8: Security Analysis, page 211-213

The data rate at which the PHY preamble was transmitted is 6 Mbps. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to detect and synchronize with the signal. The PHY preamble is always transmitted at a fixed data rate that depends on the type of PPDU (e.g., OFDM, HT, VHT, HE). For an 802.1 lac data frame on channel 52, which uses VHT PPDUs, the data rate for the PHY preamble is 6 Mbps. This data rate does not depend on MCS (Modulation and Coding Scheme), which only affects the data rate for the PSDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

The function of the PHY layer is to convert PSDUs to PPDUs for transmissions and PPDUs to PSDUs for receptions. A PSDU (PHY Service Data Unit) is the data unit that is passed from the MAC layer to the PHY layer for transmission, or from the PHY layer to the MAC layer for reception. A PPDU (PHY Protocol Data Unit) is the data unit that is transmitted or received over the wireless medium by the PHY layer. A PPDU consists of a PSDU and a PHY header, which contains information such as modulation, coding, and data rate. The PHY layer adds or removes the PHY header to or from the PSDU during the conversion process. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

A capture visualization tool is a software application that can open a packet capture file and display various graphs, charts, tables, and statistics that illustrate the characteristics and behavior of the wireless network. A capture visualization tool can help a network administrator with little knowledge of 802.11 protocols to evaluate the overall health and performance of their wireless network by providing a visual and intuitive representation of the captured data. A spectrum analyzer is a hardware device that measures the radio frequency signals in a given frequency range and displays their amplitude, frequency, and modulation. A spectrum analyzer can help identify sources of interference and noise in the wireless environment, but it cannot open a packet capture file. Python is a programming language that can be used to write scripts or applications that manipulate or analyze packet capture files, but it requires coding skills and knowledge of 802.11 protocols. A WLAN scanner is a software application that scans for available wireless networks and displays information such as SSID, BSSID, channel, signal strength, security type, and vendor. A WLAN scanner can help discover wireless networks and their basic parameters, but it cannot open a packet capture file345 References:

• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 63
• CWAP-404 Objectives, Section 2.5: Use capture visualization tools
• CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 117
• CWAP-404 Objectives, Section 4.1: Use spectrum analysis tools
• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 33
• CWAP-404 Objectives, Section 2.2: Analyze field values

A STA that supports 802.11k Radio Measurement would send a Neighbor Request to an AP to request a list of neighboring APs which the STA can use as roaming candidates. A Neighbor Request is an Action frame that contains a subelement specifying the type of information that the STA wants to receive from the AP. A Neighbor Report is an Action frame that contains a subelement with a list of neighboring APs that match the criteria specified in the Neighbor Request. The Neighbor Report provides information such as BSSID, channel, operating class, and PHY type of each neighboring AP. This information helps the STA to perform intelligent roaming decisions based on signal quality, load, and compatibility . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 434; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 12: 802.11k/v/r/u/w/ai Amendments, page 435.

The HT protection mode in which an AP is operating can be identified by looking at the HT Operations element in a Beacon frame. The HT Operations element is a part of the Beacon frame that contains information about the High Throughput (HT) capabilities and operation of an 802.11n BSS. The HT Operations element has a field called HT Protection, which indicates how the BSS protects its HT transmissions from interference or collisions with non-HT devices or BSSs. The HT Protection field can have four values: No Protection, Nonmember Protection, 20 MHz Protection, or Non-HT Mixed Mode. The other options are not correct, as they do not contain information about the HT protection mode. The HT Protection element does not exist, the ERP Information element is used for Extended Rate PHY (ERP) protection mode for 802.11g devices, and the HT Capabilities element is used for indicating the supported HT features of an individual device. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 125-126

Before a retransmission, the CWmax (Contention Window maximum) value doubles and increases by 1. The CWmax is a parameter that determines the upper limit of the random backoff time that a STA (station) has to wait before attempting to access the medium. The random backoff time is chosen from a range of values between CWmin (Contention Window minimum) and CWmax. The CWmin and CWmax values depend on the AC (Access Category) of the traffic and the PHY type of the STA. If a transmission fails due to a collision or an error, the STA has to retransmit the frame after waiting for another random backoff time. However, to reduce the probability of another collision, the STA increases its CWmax value by doubling it and adding 1. This increases the range of possible backoff values and spreads out the STAs more evenly. The STA resets its CWmax value to its original value after a successful transmission or after reaching a predefined limit. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 7: QoS Analysis, page 196-197

A PS-Poll (Power Save Poll) frame is not an 802.11 management frame. A PS-Poll frame is a type of control frame that is used by a STA in power save mode to request data frames from an AP. A STA in power save mode can conserve battery power by periodically sleeping and waking up. When a STA sleeps, it cannot receive any data frames from the AP, so it informs the AP of its power save status by setting a bit in its MAC header. The AP then buffers any data frames destined for the sleeping STA until it wakes up. When a STA wakes up, it sends a PS-Poll frame to the AP, indicating its association ID and requesting any buffered data frames. The AP thenresponds with one or more data frames, followed by an ACK or BA frame from the STA. The other options are not correct, as they are types of 802.11 management frames. An Action frame is used to perform various management actions, such as spectrum management, QoS management, radio measurement, etc. A Beacon frame is used to advertise the presence and capabilities of an AP or BSS. An Authentication frame is used to establish or terminate an authentication relationship between a STA and an AP. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 6: 802.11 Frame Exchanges, page 169-170

An HE TB PPDU (High Efficiency Trigger-Based Packet Data Unit) is used to respond with an uplink transmission to an MU-RTS trigger frame in the 802.11ax PHY (Physical Layer). An MU-RTS trigger frame is a frame that initiates a multi-user transmission opportunity (MU-TXOP) by requesting multiple stations (STAs) to send clear-to-send (CTS) frames on different spatial streams or resource units (RUs). An HE TB PPDU is a frame that contains data from multiple STAs that have been allocated RUs by an MU-RTS trigger frame or another type of trigger frame. An HE SU PPDU (High Efficiency Single User Packet Data Unit) is a frame that contains data from a single STA using all available spatial streams or RUs. An HE MU PPDU (High Efficiency Multi User Packet Data Unit) is a frame that contains data from multiple STAs using different spatial streams or RUs without being triggered by another frame. A VHT PPDU (Very High Throughput Packet Data Unit) is a frame that uses the 802.11ac PHY and does not support multi-user transmissions.References:

• CWAP-404 Study Guide, Chapter 3: 802.11 MAC Layer Frame Formats and Technologies, page 101
• CWAP-404 Objectives, Section 3.4: Analyze multi-user transmissions
• CWAP-404 Study Guide, Chapter 3: 802.11 MAC Layer Frame Formats and Technologies, page 99