JNCIS-ENT JN0-352 Passing Score

The Junos BGP path selection algorithm proceeds through a strict, ordered sequence of comparison steps, and once next-hop reachability and route preference (administrative distance) have been confirmed as equal, local preference is the very first BGP-specific path attribute evaluated in the decision process. A route carrying a higher local preference value is always chosen over a competing route to the same prefix with a lower local preference, and this comparison takes absolute precedence over every subsequent attribute in the algorithm; if local preference values differ between candidate paths, the selection process concludes at this step without ever needing to examine AS path length, origin type, or MED at all. Only when two or more competing paths share an identical local preference value does the algorithm proceed to its third step, comparing AS path length and preferring the shortest, and only after a further tie does it move on to origin type (preferring IGP-origin over EGP-origin, and EGP-origin over incomplete), followed by MED comparison (preferring the lowest value, and only among routes learned from the same neighboring AS by default). Because local preference is evaluated strictly before all three of the other listed attributes, it is the attribute BGP consults first among the choices given, making it the deciding factor in scenarios such as this exhibit where multiple autonomous systems advertise competing paths toward the same 192.168.1.0/24 prefix. Reference topics: Junos Enterprise Routing – BGP, Understanding BGP Path Selection Order.

TLV 22, the Extended IS Reachability TLV defined in RFC 5305, is the modern and Junos-preferred mechanism for advertising a router's adjacent neighbors together with the metric associated with each link. It carries the seven-octet system ID and pseudonode number of each neighbor along with a 24-bit wide metric field, and supports an extensible set of sub-TLVs used for traffic-engineering data such as interface and neighbor IP addresses, bandwidth, and administrative groups. The original IS Reachability TLV, TLV 2, defined in the base ISO 10589 standard, carries similar neighbor and metric information but is constrained to a 6-bit narrow metric with a maximum value of 63, which is inadequate for expressing meaningful cost differentiation in modern, high-capacity enterprise and service-provider topologies; consequently, Junos deployments are commonly configured for wide-metrics-only, favoring TLV 22 over the legacy TLV 2 whenever traffic-engineering-capable or simply more granular metric representation is desired. TLV 132, the IP Interface Address TLV, only advertises the IPv4 addresses configured on the originating router's interfaces and carries no neighbor-adjacency or metric information. TLV 129, the Protocols Supported TLV, merely lists which network-layer protocols (such as IPv4 or IPv6) the originating router is capable of routing, and likewise has nothing to do with neighbor reachability or link cost. Reference topics: Junos Enterprise Routing – IS-IS, Extended IS Reachability and Wide Metrics.

On EX Series switches, aggregated Ethernet (ae) interfaces do not exist by default; before any ae interface can be created, referenced, or brought into service, an administrator must first reserve the desired number of aggregated Ethernet device slots by configuring set chassis aggregated-devices ethernet device-count number at the [edit chassis] hierarchy. This statement allocates the internal resources needed for that many ae interfaces to exist as valid, configurable objects; until it is committed, any interface-level configuration referencing ae0 (such as the aggregated-ether-options and family ethernet-switching stanzas shown in the exhibit) is accepted syntactically by the CLI but never actually instantiates a live ae0 device, which is exactly why show interfaces ae0.0 returns 'device ae0 not found' despite the interface appearing fully configured. Increasing the device-count to at least 1 (or higher, to cover the number of LAG bundles planned) immediately resolves this and allows ae0 to appear as an operational interface once its member links are also associated with it. This is a foundational and frequently overlooked prerequisite step in LAG deployment on Juniper switches. There is no separate licensing requirement for aggregated Ethernet functionality on EX Series switches, a reboot is not needed since the chassis statement takes effect upon commit, and the LACP mode (active versus passive) is unrelated to whether the ae interface object itself exists in the first place. Reference topics: Junos Enterprise Switching – Link Aggregation, Configuring the Aggregated Ethernet Device Count.